Filter products
Anti-Collision Systems
Average rating of 0 out of 5 stars
Fully compatible to Original-FLARM.12 light, two colours LEDs for direction indicatorNearest-info (green) and warning (red)Above/Below with 4 LEDs (two colours)key instead of the membrane keyboardown voltage regulator 6 - 30 V DCcompatible to the displays before 1 & 2GFK-casingmetall-thread (moulded sleeve) to screw mountingMeasurement of 50 x 25 x 5,7 mmcontent with connection cable 3,5m
Average rating of 0 out of 5 stars
Latest firmware update pre-installed on a micro SD cardAvailable for PowerFLARM Fusion, PowerFLARM Core and PowerFLARM PortablePlease indicate with your order for which device you need the update.
Average rating of 0 out of 5 stars
Kit contains AIR Traffic Main Unit, AIR Traffic Display and installation accessories. AIR Traffic Main Unit: The new AIR Traffic Main Unit is a collision avoidance system. The unit transmits and receives FLARM® data via the latest PowerFLARM technology. With its two antennas and antenna diversity it also receives ADS-B data (ADS-B IN) and signals of Mode-S transponders.The flexible interface concept allows seamless integration in existing cockpit environments. It can be used with a wide range of display units (e.g. AIR Traffic Display) and navigation systems (GARMIN GTN®) or via the integrated WiFi function in combination with Apps on smartphones or tablets. The AIR Traffic unit is small, requires little power and is easy to install. It can be mounted anywhere in the cockpit. To show the traffic information to the pilot the main unit can be connect to either existing avionics or directly to an AIR Traffic Display. Minor Changes and EASA Standard Changes are available and allow a legal installation in hundreds of aircrafts.Functions: Transmits and receives FLARM® data. There are more than 35.000 FLARM® users worldwide. Receives ADS-B und Mode-S transponder signals (Mode-S transponder targets only available with vertical- and lateral distance, direction unknown)Reliable warnings to potential hazardous traffic, obstacles (optional database required) and alarm zones.Transmits GPS- and traffic data to a wide range of compatible avionics, navigation systems and Apps.Any number of data channels simultaneously possible within one aircraft. Technical Highlights: Latest PowerFLARM technologie with two antennas and antenna diversity (FLARM, ADS-B and Mode-S transponders).Multiple Interface, 3x RS232, ARINC 429, USB and WiFi integrated.Installation somewhere in the cockpit or directly to an AIR Traffic DisplayWireless communication with Apps. Configuration via website and any Smartphone, Tablet or PC.Switch inputs relays to control external electronics (e.g., ACL). Works with any internal and external antennas.Minor Change Approval available for installation in hundreds of aircrafts.Delivery: AIR Traffic Main Unit ADS-B and FLARM antenna for internal installation (cable length 1m)GPS antenna for internal installation (cable length 1.5m)D-SUB 26 HD socket housing und 6 crimp contactsDocumentation AIR Traffic Display: The AIR Traffic Display is a new display system to bring up air traffic information to the pilot. The hardware is very robust, perfect readable, even in bright sunlight and offers many functionalities to assist the pilot in collision avoidance. It can be used as display system for many other collision avoidance system e.g. TRX-, FLARM- or PowerFLARM-units. 3D air traffic information, for FLARM and ADS-B as well as 2D air traffic information for transponder signals (depended on signal information)Huge and brilliant color display – perfect readable, even in bright sunlight, intuitive usageOptical and acoustic (tone generator integrated) traffic warningsOptical and acoustic obstacle warnings (depended on connected system)Tactical information for glider pilots (thermal center information, averge climb information etc.)Traffic tracking outside reception rangeSoftware updates via microSD card. Tecnical Data: Dimensions (without knob): 61,5 x 61,5 x 30 mm57mm cockpit panel mountWeight about. 140gInputvoltage: 9 to 32V DCInterfaces: RS232 FLARM protocol and RS232 GARMIN TIS Delivery: ATD-57 DisplayScrews for mounting RJ45 cable with standard FLARM/IGC pinningDocumentation
Average rating of 0 out of 5 stars
AIR Traffic Display is our newly designed premium display solution for traffic data. It features robust hardware, a sunlight readable display and advanced functionality reducing flightcrew workload and increasing traffic awareness. Air Traffic Display works well with many collision avoidance devices like TRX, (Power)FLARM®, or systems with GARMIN® TIS interface.Display of 3D Traffic, e.g. FLARM® or ADS-B and 2D traffic e.g. Transponders (depends on connected traffic system)Brilliant, sunlight readable displayOptical and aural traffic warnings (alert sounder integrated)Optical and aural obstacle warnings (alert sounder integrated, depends on connected traffic system)Target identification via FLARMNet Database. Updateable via microSD CardTactical functions for gliderpilots (circling detection, climb-rate-filter)Tracking of targets out of reception rangeSoftware updates via microSD CardSpecsDimensions (without rotary knob): 61,5 x 61,5 x 30 mm57mm Standard Cutout (2.25")Weight ca. 140gInput Voltage: 9 to 32V DCInterfaces: RS232 FLARM Protokoll and RS232 GARMIN TIS DeliveryATD-57 main unitPanel screwsStandard RJ45 cable (FLARM/IGC compatible pinout)Documentation
Average rating of 0 out of 5 stars
Kit contains AIR Traffic Main Unit, AIR Traffic Display and installation accessories. AIR Traffic Main Unit: The new AIR Traffic Main Unit is a collision avoidance system. The unit transmits and receives FLARM® data via the latest PowerFLARM technology. With its two antennas and antenna diversity it also receives ADS-B data (ADS-B IN) and signals of Mode-S transponders.The flexible interface concept allows seamless integration in existing cockpit environments. It can be used with a wide range of display units (e.g. AIR Traffic Display) and navigation systems (GARMIN GTN®) or via the integrated WiFi function in combination with Apps on smartphones or tablets. The AIR Traffic unit is small, requires little power and is easy to install. It can be mounted anywhere in the cockpit. To show the traffic information to the pilot the main unit can be connect to either existing avionics or directly to an AIR Traffic Display. Minor Changes and EASA Standard Changes are available and allow a legal installation in hundreds of aircrafts.Functions: Transmits and receives FLARM® data. There are more than 35.000 FLARM® users worldwide. Receives ADS-B und Mode-S transponder signals (Mode-S transponder targets only available with vertical- and lateral distance, direction unknown)Reliable warnings to potential hazardous traffic, obstacles (optional database required) and alarm zones.Transmits GPS- and traffic data to a wide range of compatible avionics, navigation systems and Apps.Any number of data channels simultaneously possible within one aircraft. Technical Highlights: Latest PowerFLARM technologie with two antennas and antenna diversity (FLARM, ADS-B and Mode-S transponders).Multiple Interface, 3x RS232, ARINC 429, USB and WiFi integrated.Installation somewhere in the cockpit or directly to an AIR Traffic DisplayWireless communication with Apps. Configuration via website and any Smartphone, Tablet or PC.Switch inputs relays to control external electronics (e.g., ACL). Works with any internal and external antennas.Minor Change Approval available for installation in hundreds of aircrafts.Delivery: AIR Traffic Main Unit ADS-B and FLARM antenna for internal installation (cable length 1m)GPS antenna for internal installation (cable length 1.5m)D-SUB 26 HD socket housing und 6 crimp contactsDocumentation AIR Traffic Display: The AIR Traffic Display is a new display system to bring up air traffic information to the pilot. The hardware is very robust, perfect readable, even in bright sunlight and offers many functionalities to assist the pilot in collision avoidance. It can be used as display system for many other collision avoidance system e.g. TRX-, FLARM- or PowerFLARM-units. 3D air traffic information, for FLARM and ADS-B as well as 2D air traffic information for transponder signals (depended on signal information)Huge and brilliant color display – perfect readable, even in bright sunlight, intuitive usageOptical and acoustic (tone generator integrated) traffic warningsOptical and acoustic obstacle warnings (depended on connected system)Tactical information for glider pilots (thermal center information, averge climb information etc.)Traffic tracking outside reception rangeSoftware updates via microSD card. Tecnical Data: Dimensions (without knob): 61,5 x 61,5 x 30 mm57mm cockpit panel mountWeight about. 140gInputvoltage: 9 to 32V DCInterfaces: RS232 FLARM protocol and RS232 GARMIN TIS Delivery: ATD-57 DisplayScrews for mounting RJ45 cable with standard FLARM/IGC pinningDocumentation
Average rating of 0 out of 5 stars
Das neue AIR Traffic Kollisionswarnsystem sendet und empfängt FLARM® Daten über neueste PowerFLARM Technologie mit zwei Antennen und Antenna Diversity.Weiterhin empfängt es ADS-B Daten (ADS-B IN) und Signale von Mode-S Transpondern. Sein flexibles Schnittstellenkonzept erlaubt die nahtlose Einbindung in bestehende Cockpits.Es ist mit Anzeigegeräten, Navigationssystemen (auch IFR GPS wie GARMIN GTN®) oder durch die integrierte WiFi Funktion sogar drahtlos mit Apps nutzbar.AIR Traffic ist klein, benötigt wenig Strom und ist einfach zu installieren.Es kann verdeckt installiert und mit bestehenden Bordsystemen verbunden werden. Weiterhin ist es möglich, es direkt am AIR Traffic Display als kompakte Einheit im Instrumentenbrett unterzubringen.Minor Changes und EASA Standard Changes sind verfügbar und erlauben den legalen Einbau in hunderte von Luftfahrzeugtypen.Funktionen:Sendet und Empfängt FLARM Verkehrsdaten, d.h. es erkennt über 35.000 FLARM® Nutzer weltweit und wird auch von diesen erkanntEmpfängt ADS-B und Mode-S Transponderdaten (Mode-S Transponder werden nur in vertikaler und horizontaler Entfernung erfasst, die Richtung kann nicht ermittelt werden)Warnt zuverlässig vor gefährlichem Verkehr, Hindernissen (optional, Datenbank erforderlich) und AlarmzonenLiefert GPS und Verkehrsdaten an hunderte von kompatiblen Anzeigesystemen, Navigationssystemen und Apps. Beliebig viele Datenkanäle gleichzeitig in einem LFZ möglich Technische Highlights:Verkehrstechnologie neuester Generation mit mehreren Antennen, Antenna Diversity, FLARM, ADS-B und Mode-S TransponderempfangVielseitige Schnittstellen, 3x RS232, ARINC 429, USB und WiFi direkt integriertKann verdeckt an beliebger Stelle oder direkt am AIR Traffic Display montiert werdenDrahtlose Kommunikation mit Apps und drahtlose Konfiguration über eine Webseite von jedem Smartphone, Tablet oder PC ausSchalter-Eingänge, Relais zur Steuerung externer Elektronik (z.B. ACL), arbeitet mit beliebigen internen und externen Antennen zusammenMinor Change Approval verfügbar zum Einbau in hunderte Luftfahrzeuge (optional)Maße Gehäuse: ca. 12 x 6 x 3 cmLieferumfang:AIR Traffic HauptgerätADS-B und FLARM Innenantennen mit Kabellänge 1mGPS Innenantenne mit Kabellänge 1,5mD-SUB 26 HD Buchsenkörper und 6 CrimpkontakteDokumentation
Average rating of 0 out of 5 stars
New and extra-large traffic display, for installation in 80mm panel cutouts.The AIR Traffic Display series is a high sophisticated display system for air traffic data. The hardware is very robust; the display is perfectly readable even in bright sunlight and provides many features to assist pilots in collision avoidance.The new AIR Traffic Displays where developed from scratch with the entire manufacturers experience and the results of current research. The ultimate goal is to assist the pilot in collision avoidance in the best possible way. Therefore the displays offer more traffic overview, simple to use interface and better readability. Both FLARM®, and ADS-B and transponder data can be displayed.The unit works directly with AIR Traffic, TRX devices, FLARM® devices, PowerFLARM® devices, LX-FLARM, and many other devices without any additional configurations. In additiona a connection with GARMIN® GDL90 and GARMIN® TIS® compatible collision warning systems and traffic receivers is also possible.With the optional mounting bracket, the AIR Traffic Display 80 can be directly attached to an AIR Traffic (AT-1) and installed as one unit. The AIR Traffic Display is covered by the Minor Change Approvals and EASA Standard Changes for common FLARM® systems and may therefore be installed in a wide range of aircraft. Features:Display of 3D Traffic, e.g. FLARM® or ADS-B and 2D traffic e.g. Transponders (depends on connected traffic system)Brilliant, sunlight readable display, extra-large with 2.7" screen diameterOptical and aural traffic warnings (alert sounder integrated)Optical and aural obstacle warnings (alert sounder integrated, depends on connected traffic system)Target identification via FLARMNet Database. Updateable via microSD CardTactical functions for glider pilots (circling detection, climb-rate-filter)Tracking of targets out of reception rangeSoftware updates via microSD Card Technical specifications:Dimensions (without rotary knob): 83 x 83 x 26 mmeasy-to-install into 80mm standard cutout.Input Voltage: 9 to 32V DCInterfaces: RS232 FLARM Protocol and RS232 GARMIN TIS Delivery:ATD-80 main unitPanel screwsStandard RJ45 cable (FLARM/IGC compatible pinout)Documentation
Average rating of 0 out of 5 stars
New and extra-large traffic display that fits in every cockpit.The AIR Traffic Display series is a high sophisticated display system for air traffic data. The hardware is very robust; the display is perfectly readable even in bright sunlight and provides many features to assist pilots in collision avoidance.The new AIR Traffic Displays where developed from scratch with the entire manufacturers experience and the results of current research. The ultimate goal is to assist the pilot in collision avoidance in the best possible way. Therefore the displays offer more traffic overview, simple to use interface and better readability. Both FLARM®, and ADS-B and transponder data can be displayed.The unit works directly with AIR Traffic, TRX devices, FLARM® devices, PowerFLARM® devices, LX-FLARM, and many other devices without any additional configurations. In additiona a connection with GARMIN® GDL90 and GARMIN® TIS® compatible collision warning systems and traffic receivers is also possible.The AIR Traffic Display is covered by the Minor Change Approvals and EASA Standard Changes for common FLARM® systems and may therefore be installed in a wide range of aircraft. Features:Display of 3D Traffic, e.g. FLARM® or ADS-B and 2D traffic e.g. Transponders (depends on connected traffic system)Brilliant, sunlight readable display, extra-large with 2.7" screen diameterOptical and aural traffic warnings (alert sounder integrated)Optical and aural obstacle warnings (alert sounder integrated, depends on connected traffic system)Target identification via FLARMNet Database. Updateable via microSD CardTactical functions for glider pilots (circling detection, climb-rate-filter)Tracking of targets out of reception rangeSoftware updates via microSD Card Technical specifications:Dimensions (without rotary knob): 100,5 x 50,5 x 22 mmExternal, easy-to-install, Weight ca. 140gInput Voltage: 9 to 32V DCInterfaces: RS232 FLARM Protokoll and RS232 GARMIN TISDelivery:ATD-11 main unitStandard RJ45 cable (FLARM/IGC compatible pinout)Documentation
Average rating of 0 out of 5 stars
ADS-B IN/OUT with FLARM CapabilitySkyEcho includes FLARM and ADS-B receivers to receive position reports from other equipped aircraft and display them on in-flight applications, including ForeFlight Mobile, SkyDemon, EasyVFR, and AirMate. *Portable ADS-BSkyEcho 2 is a portable ADS-B receive and transmit solution. With 20W transmit power, your 1090MHz ADS-B signal can be received up to 40NM away. Transmit functionality can be enabled or disabled depending on your flight location. The ADS-B receiver capability includes both 1090MHz and 978MHz UAT. Portable ADS-B transmit capability is currently only approved for use in the United Kingdom under CAP1391.FLARM Reception CapabilityReceive FLARM in the UK/EU natively with SkyEcho 2. When selected by the user, the UAT radio in SkyEcho 2 can be used as a FLARM receiver. FLARM traffic data is transmitted to participating EFB applications for display of FLARM traffic. SkyEcho 2 will translate the FLARM data onto your compatible EFB along with the ADS-B traffic.Integrated AltimeterSkyEcho 2 includes an integrated baro altimeter. The altimeter correlates cabin pressure altitude to altitudes of nearby traffic to give you more accurate relative altitude alerts.No Clutter CockpitThe integrated uAvionix SkyEcho 2 battery removes cords and clutter from the cockpit and has enough capacity for up to 12 hours of flight time with the transmit function enabled.Connect wirelessly to SkyEcho and receive live traffic on your GDL90 compatible EFB or EFIS for up to 4 devices simultaneously.TECHNICAL SPECIFICATIONS:Operating Time 12 hoursSize: 57x82x30 mmWeight: 120 gOperating Temp -45 to 70 CWAAS GPSWi-Fi 802.11 b/g/n 2.4GHz4 simultaneous ConnectionsPorts: USB-C* The decoding of the FLARM signal is done via the navigation app. The app providers charge licence fees for FLARM decoding, e.g. via in-app purchases. for SkyDemon: https://www.skydemon.aero/Store/Plates/flarmdecoding *for SkyMap: https://www.sky-map.de/order.php (ganz unten) *for ForeFlight: https://support.foreflight.com/hc/en-us/articles/360050274413-How-can-FLARM-traffic-be-received-and-displayed-in-ForeFlight-Mobile-using-the-SkyEcho-2 *for Airmate: https://www.airmate.aero/shop/?product=airmate-application-ios&lang=en *for für EasyVFR: https://www.easyvfr4.aero/shop/add-ons/ev4-app-add-on/flarm-skyecho-2-easyvfr-4 *Licence fees for FLARM use are not included in the purchase price of the SkyEcho 2.
Average rating of 0 out of 5 stars
PowerFLARM Fusion ist die Weiterentwicklung des beliebten PowerFLARM CORE für den Segelflug.Es kombiniert die robuste und bewährte PowerFLARM Technologie mit einer benutzerfreundlichen Bedien- und Wartungsoberfläche (FLARM Hub).FLARM Hub bietet die Möglichkeit, Updates der Firmware & Hindernisdatenbank durchzuführen, sowie IGC-Dateien direkt auf den Computer oder ein mobiles Gerät zu laden. Zusätzlich enthalten sind eine Flugverkehrsanzeige, eine bidirektionale Datenschnittstelle sowie Werkzeuge zur Funkreichweitenanalyse und für Diagnose & Support.PowerFLARM Fusion bietet eine große Bandbreite an Bluetooth und Wi-Fi Verbindungsoptionen und kann mit bekannten Navigationssystemen wie iGlide und XC Soar gekoppelt werden. Zusätzlich zum FLARM Datenprotokoll (ICD) wird das GDL 90 Protokoll unterstützt, welches von vielen EFBs und Navigationssystemen verwendet wird.FLARM Monitore und anderes Zubehör sind in Hülle und Fülle von verschiedensten Herstellern verfügbar.Die ähnlichen Antennen und Datenverbindungen des PowerFLARM Fusion erlauben ein Upgrade des PowerFLARM Core fast spielerisch. Die Dimension und Anschlagpunkte der beiden Geräte sind identisch.Ein Adapter-Kit für die neuen, verbesserten Antennenstecker ist optional verfügbar, wodurch keine weiteren Änderungen der bestehenden Infrastruktur notwendig sind.Technische DatenMaße: 119 x 80 x 42 mmGewicht: 250 gSpannungsversorgung 12–32 V DC ±5%, Stromaufnahme (ohne externe Verbraucher) 200 mA @ 12 V DC (maximal) 180 mA @ 12 V DC (typisch), Versorgung für externe Geräte 1 x 250 mA @ 3 V DC (D-SUB, RJ45), 1 x 700 mA @ 5 V DC (D-SUB, USB)Daten Schnittstellen D-SUB-9 und RJ45Kabellose Verbindungen FLARM ICD: Wi-Fi (TCP, WebSocket) und Bluetooth LEGDL 90: Wi-FiWeitere Informationen:Audio Schnittstelle AC, 1.7 V peak-to-peak @ 1 k?GPS SMC Anschluss(FLARM) RP-SMA Anschluss (2x)868 bis 869 MHz (SRD860-band) und (SSR/ADS-B) SMA AnschlussUSB Anschluss für USB-Sticks (USB 2.0)Zubehör Interne Antennen & Kabel (beinhaltet)Lieferumfang:PowerFLARM Fusion GerätGPS-Antenne WeltweitAnschlusskabel 9-polig SubD2 Stück FLARM-Innenantennen EuropaTransponder-Empfangsantenne WeltweitUSB-Verlängerung für die Panelmontage
Average rating of 0 out of 5 stars
The f.u.n.k.e. AVIONICS TM350 is a compact avionics module for airspace monitoring and proximity warning. It receives and processes ADS-B, Mode S, Mode A/C and FLARM signals to help the pilot assess the surrounding traffic situation. Traffic information is supplied to connected cockpit displays, external indicators or compatible navigation apps.The information available depends on the transmissions received and the equipment configuration. Detecting a signal is different from decoding precise position data. In particular, the standard FLARM reception capability differs from the optional upgrade that enables full position processing.An integrated FLARM beacon transmits FLARM messages, allowing the aircraft to be detected by suitably equipped FLARM systems. In the standard configuration, incoming FLARM signals are evaluated by signal strength. Nearby FLARM traffic is reported without precise position information. Full internal FLARM reception with position decoding requires an optional licence. An external FLARM device can be connected as an alternative.Serial RS232 interfaces and WiFi provide connections to displays and navigation systems. Supported output protocols include GDL90, FLARM and NMEA. The manufacturer lists SkyDemon, ForeFlight and VFRnav among the compatible navigation apps. The connection and output protocol are configured to suit the receiving system.Setup is carried out through a browser-based WiFi interface, which provides access to device parameters and interface settings. Two simultaneous WiFi connections are supported for wireless data transfer. An ARINC429 interface is available as an option.When connected to a suitable extended-squitter-capable transponder, the TM350 can form part of an ADS-B In/Out system. The aircraft’s own ADS-B position is transmitted by the transponder. The TM350 alone does not replace an ADS-B Out transponder. The manufacturer provides optimised integration with the f.u.n.k.e. TRT800H and TRT800A transponders.The module measures 35 × 65 × 115 mm and weighs approximately 250 g including the mounting plate. Its operating voltage is 11–30 V DC. This product includes the TM350 and its mounting plate. The required antennas and connecting cables must be ordered separately.Features- Traffic reception and proximity warning- Processing of ADS-B, Mode S, Mode A/C and FLARM signals- Integrated FLARM beacon- FLARM proximity detection without position decoding in the standard configuration- Full FLARM reception available as an option- Output to external displays and compatible navigation apps- Configuration through a browser-based WiFi interfaceTechnical specifications- Operating voltage: 11–30 V DC- Dimensions: 35 × 65 × 115 mm- Weight: approx. 250 g including mounting plate- Serial interfaces: 4 × RS232- WiFi: 802.11 b/g/n, two simultaneous connections- Output protocols: GDL90, FLARM, NMEA- ARINC429: optionalScope of delivery- f.u.n.k.e. AVIONICS TM350- Mounting plateOrdering and operating notesAntennas and connecting cables are not included. Full FLARM reception and ARINC429 are optional functions and must be considered when specifying the installation.The TM350 supports traffic awareness. It does not provide avoidance instructions or replace the pilot’s responsibility for safe flight.
Average rating of 0 out of 5 stars
Portabler ADS-B, FLARM und GPS-Empfänger, inkl. CO-Sensor Tragbarer ADS-B-Empfänger der nächsten Generation aus dem Hause ForeFlight. Sentry PLUS baut auf den Fähigkeiten früherer Geräte auf und ist mit innovativen neuen Funktionen ausgestattet. Produktmerkmale Sentry PLUS:Bis zu 18 Stunden Akku-LaufzeitEingebautes OLED-Display informiert Sie über Verbindungs- und Gerätestatus sowie aktuelle Flugdaten wie G-Load, GPS-Genauigkeit usw.Automatische Trackaufzeichnung mit problemlosem Upload zur ForeFlight-ApplikationAHRS Backup Attitude & G-Meter durch integrierten Lagesensor - Durch flexible Kalibrierungsoptionen erhlaten Sie genaue AHRS-Daten, egal wo der Sentry PLUS im Flugzeug befestigt istEingebauter Kohlenmonoxid-Monitor inkl. akkustischem und optischem Alarmsystem (mit Audio und App-Alarm)Dynamische Verkehrsanzeige in der ForeFlight-App von Luftfahrzeugen mit ADS-B Out- und FLARM-Signalen (Für die Darstellung von FLARM-Signalen muss eine zusätzliche Lizenz bei foreflight.com/buy erworben werden!)Hochpräzise WAAS GPS Anzeige zur optimalen und genauen Darstellung der Flugzeugposition auf der Karte in Ihrer ForeFlight-App.Einfaches Setup der WiFi-Verbindung dank des OLED DisplaysGleichzeitige Verbindung von bis zu 5 Geräten mittels WLANKompakte Abmessungen von ca. 10,7 cm x 8,6 cm x 3,8 cmGewicht ca. 210 gLieferumfang: ForeFlight Sentry PLUS, USB-C Kabel, RAM® Saugnapf mit Schnellverschluss-Adapter, Tragebeutel, Schnellstartanleitung in Englisch Hinweis: Sentry PLUS funktioniert ausschließlich mit der ForeFlight-App! Externe Antennen können nicht angeschlossen werden.
Average rating of 0 out of 5 stars
The Most Full-featured Portable ADS-B & GPS Receiver is now coming with improved GPS receiver performance, improved charger compability, and finally improved durability.With an integrated CO monitor and alarm and 12 hours of battery life, Sentry has everything you expect in an ADS-B receiver and more. Knowing what’s around you is just as important as knowing what’s in front of you.With Sentry you can access subscription-free FIS-B weather & data. Display animated regional and CONUS NEXRAD, METARs, TAFs, AIR/SIGMETs, PIREPs, textual winds and temps aloft, TFRs, NOTAMs, and SUA information on ForeFlight Mobile.A first for portable ADS-B receivers, Sentry provides a built-in carbon monoxide sensor and alerting system, with an audio and in-app alert when CO concentration reaches hazardous levels. The LED indicator also provides a visual indication of CO levels.Pilotage meets the 21st century with Sentry’s highly-accurate WAAS GPS. See your aircraft position on ForeFlight’s moving map display and innovative Plates on Map feature.Sentry uses both GPS and GLONASS GNSS constellations and can make use of satellite based augmentation systems like WAAS for high-precision positioning and increased redundancy. View a variety of inflight data, including ground speed, altitude, ETE, distance to destination, and more.Features:Sentry’s Attitude Heading Reference System (AHRS) provides a real-time depiction of your aircraft’s pitch and bank in ForeFlight. Flexible calibration options allow you to get accurate AHRS data no matter where you mount Sentry in your aircraft.Sentry’s efficient power usage allows 12 hours of continuous operation on a single charge, providing non-stop situational awareness for the long haul.If you’ve got room for a deck of cards in your aircraft, you’ve got room for Sentry.Large enough to not get lost under the seat, yet small enough that it doesn’t block your view, and the internal battery makes charging simple and straightforward.Sentry’s quick release mechanism means you can attach and remove it in under a second. The popular RAM® suction cup mount ensures a long-lasting seal and high heat tolerance so you can leave it in the plane between flights.Sentry has a light sensor to detect the ambient light level and automatically adjust its LED brightness accordingly. You can also disable this setting to manually set the brightness.Sentry’s integrated Wi-Fi network supports up to 5 devices.Use ForeFlight’s Cockpit Sharing feature to quickly and easily share routes between all devices on Sentry’s network - perfect for your co-pilot and passengers to follow along as extra eyes on traffic and weather.Updating Sentry’s firmware is a non-issue thanks to fast over-the-air updates through ForeFlight. When an update is available, ForeFlight provides one-tap installation that finishes in seconds.Dimensions of the new model are 60 x 83 x 36 mm (WxHxD)Delievery includes ForeFlight Sentry ADS-B Receiver, USB cable, Suction Cup, Carrying Case, Quick Start Guide (EN).
Average rating of 0 out of 5 stars
Product Information “PowerFLARM Flex with Battery”The portable solution featuring a high-performance FLARM transmitter and receiver, transponder receiver, Wi-Fi, and Bluetooth.Also of interest to glider pilots thanks to its built-in IGC and ENL.Warnings are displayed in the proven LED ring, while situational awareness is shown on the small graphic screen. The device has a battery compartment for a standard lithium-ion battery and runs for at least one day of flying. Charging is done directly in the device using a USB-C charging cable.The PowerFLARM Flex’s user interface makes configuration simple and intuitive. The interface can be accessed directly from any smartphone, tablet, or computer/Mac.This allows you to perform firmware updates, update the obstacle database, and activate features, as well as save IGC files directly to your computer or mobile device.PowerFLARM Flex offers a wide range of Bluetooth and Wi-Fi connection options and can be paired with popular navigation systems such as Air Navigation Pro, SkyDemon, ForeFlight, EasyVFR, iPilot, and XC Soar.In addition to the FLARM data protocol (ICD), the GDL 90 protocol is supported, which is used by many apps by default.The device’s design and dimensions allow for direct mounting on the instrument panel. The device is an ideal replacement for the Clas units—some of which are already 20 years old—mounted on many glider instrument panels.Installing safety features on an airplane has never been easier than it is today.Technical SpecificationsDimensions: 12 cm x 9 cm x 4 cmWeight: approx. 225 gFLARM, 1090 ADS-B, and transponder detectionWi-Fi, Bluetooth LEGNSSPowered by a replaceable lithium-ion battery (not included)Charging via USB-C (5 V)RJ-45 (up to 34 V)High-dynamic LED display for warningsHigh-resolution LCD display for awareness visualizationOperation via rotary pushbutton or web user interfaceAudible alertRS-232 data interface via RJ-45 jackGDL90 data protocolConfiguration and updates via the FLARM Hub web app (Wi-Fi)Package contents:PowerFLARM Flex unitPadded carrying caseUSB-C to USB-A charging cableCompatible Li-ion battery
Average rating of 0 out of 5 stars
Lithium-ion Batterie 18650Passend für PowerFLARM FlexSicherheitshinweise:- Lithium Zellen dürfen nur mit Schutz-Elektronik betrieben werden!- Bitte beachten Sie, dass Lithium Zellen nur durch fachkundige Personen verwendet werden dürfen- Bei falscher Handhabung bzw. Kurzschluss kann es zur Brandentwicklung oder Explosion führen